Two Hole Strap for EMT Conduit: Sizes, Uses, and Selection Guide

A two-hole strap for EMT conduit is a support fitting that fastens a run of electrical metallic tubing to a mounting surface through two screw or anchor points. To select one, match the strap’s intended conduit trade size to the EMT, then confirm its material, mounting-hole dimensions, finish, and installation environment. Common EMT trade-size examples include 1/2-in, 3/4-in, and 1-in; these labels are nominal trade sizes, so buyers should verify the product drawing rather than assume the strap’s inside dimensions from the label alone. This guide explains the strap’s uses, size matching, purchasing considerations, and the information to prepare for a supplier inquiry.

Read more

Key Takeaways

• Match a two-hole strap to the EMT trade size and verify its fit against a drawing or sample.
• Choose material and finish based on the installation environment and compatibility with the conduit and fasteners.
• Confirm hole spacing, hole diameter, strap width, and thickness before approving an order.
• Follow project specifications and applicable electrical requirements for support placement and installation.
• For a quotation, provide size, material, finish, order quantity, and any dimensional or packaging requirements.

Who This Guide Is For

This guide is intended for electrical contractors, distributors, OEM purchasing teams, project buyers, and importers sourcing EMT conduit supports. It is also useful for buyers comparing strap options before preparing a bill of materials. The selection principles apply whether you are purchasing for a single project or evaluating a recurring supply program. Where project requirements or local rules differ, use the project documents and consult the responsible electrical professional.

What a Two-Hole EMT Strap Does

The strap wraps around or bears against the outside of an EMT conduit and is secured to a supporting surface with two fasteners. Its primary job is to hold the conduit in its intended position and reduce unwanted movement at the supported point. The two mounting holes distribute attachment across two locations, but the strap alone does not determine the complete support design. Support spacing, fastener selection, and installation details must be checked against applicable codes, project specifications, and the mounting material.

Typical Applications

Two-hole straps are used to secure EMT along walls, ceilings, framing, equipment panels, and other suitable surfaces. They may be selected for exposed conduit runs where a stable, visible attachment is desired, or where the installation detail calls for two fasteners at each support. In industrial, commercial, and residential work, the appropriate configuration depends on the substrate, exposure conditions, conduit route, and project requirements. A strap should not be treated as a substitute for a specified fitting or support method where the design calls for something different.

Sizes, Materials, and Specifications

Straps are commonly identified by the EMT trade size they are designed to support. Examples include 1/2-in, 3/4-in, and 1-in EMT, but a product description alone may not show every dimension needed for a reliable fit. EMT trade size is not a direct measurement of the conduit’s outside diameter. For this reason, confirm the strap’s stated compatibility and compare the drawing dimensions with the actual conduit or project specification.

Dimensions to Confirm Before Ordering

• Conduit trade size: Identify the EMT size required by the bill of materials.
• Strap profile: Check the inside clearance and shape against the conduit and installation detail.
• Mounting holes: Confirm hole diameter, center-to-center spacing, and compatibility with the specified fasteners.
• Strap body: Review width, thickness, edge finish, and any formed features shown on the product drawing.
• Material and finish: Specify the required base material and surface treatment based on the environment and project documentation.

Metal options and finishes vary by supplier and product design. Buyers should not assume that every strap is suitable for wet, corrosive, outdoor, or high-temperature conditions simply because it is metallic. Check the supplier’s material description and confirm compatibility with the conduit, fasteners, and surrounding environment. If the project requires a particular coating, alloy, or documented property, state that requirement in the inquiry and request confirmation before purchase.

SIOSAN Product Page

How to Select the Right Strap

1. Start with the project schedule. Record the EMT trade size, quantity, installation location, and any specified material or finish.
2. Match the strap to the conduit. Use the supplier’s compatibility information and drawing dimensions, not visual estimation alone.
3. Check the mounting interface. Verify that the two holes accommodate the planned fasteners and suit the wall, framing, or equipment surface.
4. Review environmental requirements. Consider moisture, chemicals, temperature, and possible contact with dissimilar materials, then confirm the specified material and finish are appropriate.
5. Confirm installation requirements. Check project documents and applicable electrical requirements for support method, placement, and fastener details.
6. Approve a sample or drawing where needed. For repeat orders or tight dimensional requirements, request a pre-production drawing or sample review before committing to volume.

Common Selection Mistakes

A frequent mistake is ordering by trade size alone without checking the strap’s actual profile and hole locations. Another is choosing a finish based only on appearance, without considering exposure or compatibility requirements. Buyers can also overlook fastener fit, mounting-surface limitations, or packaging needs that affect receiving and installation. Resolving these details before production or shipment can reduce avoidable substitutions and order clarifications.

Pricing, MOQ, and Lead-Time Considerations

The purchase price for a two-hole strap may depend on its dimensions, material, finish, order quantity, packaging, and whether the item is a standard configuration or requires customization. Minimum order quantities and lead times are supplier- and order-specific, so they should be confirmed rather than assumed. A custom hole pattern or finish may require drawing approval and additional production coordination. When requesting a quote, ask the supplier to identify the quoted specification, MOQ, production lead time, shipping terms, and any sample or tooling charges that apply.

Supplier Evaluation Checklist

A dependable sourcing process starts with a clear, comparable specification. Ask prospective suppliers to confirm the conduit trade size, material, finish, key dimensions, and packaging in writing. Review whether their quotation reflects your drawing or sample, and clarify how proposed substitutions will be communicated. For ongoing programs, discuss order planning, inspection documentation available for the product, and how revisions to drawings or specifications will be controlled.

• Can the supplier provide a dimensioned drawing for the requested size?
• Are material and finish clearly identified in the quotation?
• Can the supplier confirm hole dimensions and fastener compatibility?
• Are MOQ, lead time, packaging, and shipping terms stated clearly?
• Can the supplier review custom requirements before order confirmation?

Working with SIOSAN

At SIOSAN, we support B2B buyers evaluating conduit support products and related metal-component sourcing requirements. To help us assess a two-hole EMT strap inquiry, share the required trade size, material and finish, drawing or sample if available, quantity, destination, and target delivery schedule. If you are sourcing alongside aluminum pipe or other project components, include those requirements separately so the quotation scope is clear. Product availability, customization options, minimum quantities, and lead times should be confirmed for each inquiry.

Conclusion: Next Steps for Buyers

A two-hole strap secures EMT conduit to a suitable surface using two mounting points, but the right selection involves more than matching a size label. Confirm the EMT trade size, strap dimensions, hole spacing, fastener fit, material, and finish against the project requirements before ordering. Then verify support and installation details with the applicable project documents and electrical requirements. Send SIOSAN your specification, quantity, and delivery needs to discuss a suitable product configuration and request a quotation.