What the advantages and operation disadvantages of concrete block

With the development of the country, the cement brick making machine has also brought great benefits to people. UNIK cement brick making machine is to use waste, waste rock powder, waste slag, fly ash, waste ceramsite slag, smelting slag, construction waste materials to produce cement bricks, which plays the role of waste utilization; the produced bricks have high strength, High-density, non-slip, is a high-tech product that meets the requirements of environmental society and policies. The brick machine can also change the mold to produce various types of colored bricks, cement bricks, grass-planting bricks, river slope protection bricks, roadside stones, etc. It is paved on both sides of the road to enhance environmental protection, beautify the environment, and form a sharp visual contrast with traditional concrete prefabrication. At the same time, the products produced by the brick machine can be used to lay roads beside roads. The laying of cement bricks makes the products of cement bread brick making machines environmentally friendly, compressive, economical, and convenient for construction. It has been obtained in public engineering practice. It is fully embodied; it can also be used for public construction such as municipal, highways, and residential areas, etc., which is not only environmentally friendly, but also has good economic and social benefits.

Read more

Cement brick making machine can have different types of large, medium and small production lines at different price points according to different needs. The cement bread brick making machine produced by Yinma can not only produce green, environmentally friendly, low-cost, high-strength cement bricks, but also can produce various blind road bricks, curb stones, lawn bricks, interlocking bricks by changing molds. Hydraulic bricks, water channel bricks, porous bricks, hollow bricks, maple leaf bricks, I-shaped bricks, cutaway bricks, ribbed bricks, Dutch bricks, beveled side stones, thermal insulation blocks, cross-hole interlocking blocks, curved pull-hole blocks And so on, it truly realizes the multi-purpose function of one machine. It can meet the multi-faceted needs of the building materials market. It can also be configured according to the requirements for the degree of automation.

However, no matter how good the equipment is, if it is not operated strictly according to the instructions, it will not be able to produce good brick products. Therefore, when making concrete bricks and making machine-made bricks, we must also consider its maintenance and maintenance, so that its service life will not be affected. To do the following:

1. The equipment shall not be used in the open air, and must be installed in a workshop with complete water source, power supply, compressed air and dust-proof measures. The standard ambient temperature of the workplace is 5° to 40°C, the extreme low temperature of the environment shall not be lower than 0°C, and the extreme high temperature of the environment shall not be higher than 45°C. If the ambient temperature is too high, forced cooling measures must be taken to cool down; if the ambient temperature is lower than 0 °C, the raw materials used to make the blocks must have special structural components that resist low temperature.

2. When the ambient temperature of the workplace may be lower than 0 ℃, the water source must be cut off wherever there is water, such as the water metering system of the mixer and the water cooling system of the hydraulic station. Clean up the water in the water pump, cooler and pipeline. Then store the hydraulic oil of the hydraulic station in the oil tank. And take measures to keep the fuel tank warm. Especially in the cold northern regions, pay more attention.

3. All kinds of personnel who are going to install, debug, operate and maintain the production line must have the educational level of secondary technical school or above, and must be trained before taking up the job, and only after passing the qualification can they work with a certificate.

Goto Linyi Birck Mate Machinery to know more.

4. After the machinery and equipment are transported to the place designated by your company, please send personnel to unpack and inspect the goods according to the packing list in time. After confirming that the equipment is correct, please keep the equipment properly rain-proof, moisture-proof and rust-proof (including random Arrived accessories and wearing parts). If there is any error, please contact the sales center of our company in time.

5. Before installing the equipment, please measure and check all parts of the foundation according to the foundation map, and then install the equipment after confirming that it is correct.

6. To make different blocks, there are different requirements for the particle size of the materials used: when making non-porous bricks, the maximum particle size of the aggregate cannot exceed 10 mm; when making perforated bricks, the aggregate particle size should not be greater than the minimum size of the brick. 1/3 of the wall thickness.

☎ + (86)

✉ 

✓ www.unikblockmachine.com